Completed

projects

Wall formwork

The ultraMAX S wall formwork from Mayer Schaltechnik showed what it could do during the construction of this modern bowling centre.

Blank, a contractor based in Helmstadt, won the tender for the structural works on this project. Large, flat wall surfaces dominate this new games centre. The architect included a total of 1585 m² of class 2 fair-face concrete in the tender.

Lightweight formwork proves ideal for fitness studio construction

Mömlingen-based contractor Marquart used ultraMAX L aluminium wall panel formwork for the first time on this project to build more than 1000 m² of in situ concrete walls above and below ground.
Marquart ordered about 240 m² of this lightweight system from Mayer Schaltechnik. The formwork was used to construct the watertight external walls to the basement garage, all the walls to the stair and lift shafts plus the downstand beams on all floors. The low weight of the system was especially praised.

Fitness studio, Marktheidenfeld

ultraMAX L ‒ the universal module | Contractor: Marquart, Mömlingen

New church with bonus functions

Some 1300 m² of in situ concrete cast in different lift heights using PRIMAX formwork
Stiffness and dimensional accuracy even under the full weight of the wet concrete

The construction of the new Protestant-Methodist church with its basement parking, child daycare centre and apartments demonstrated the flexibility and efficiency of the PRIMAX formwork from Mayer Schaltechnik.

Church, Stuttgart-Feuerbach

PRIMAX telescopic formwork | Contractor: Bürkle, Fellbach

Telescopic beam formwork for demanding specifications

Project brief:

Class SB 3 fair-face concrete with special requirements according to the DBV recommendations
Interior faces: smooth surface
Other faces: rough-sawn boards
Consistent joint and tie patterns with minimal tie points
All corners square without bleeding

Secondary school, Osterburken

PRIMAX telescopic formwork | Contractor: Boller, Distelhausen

Concrete ensures quality drinking water

Mayer Schaltechnik PRIMAX formwork used for water reservoir in Erlangen

The reservoir had to be built according to the standards of the DVGW (German Technical & Scientific Association for Gas & Water). One of their requirements is that all concrete surfaces in contact with drinking water must have as few pores as possible.

Water reservoir, Erlangen

PRIMAX telescopic formwork | Contractor: Ulsenheimer Bau, Lichtenau

Clever formwork for challenging structural works

CCM Europe, a subsidiary of Carlisle, the US market leader for single-layer waterproofing systems, has invested €42 million in a new production plant in Waltershausen right in the centre of Germany. Two imposing production buildings plus a distinctive office building have been built on a 50 000 m² plot.

Production plant, Waltershausen

ultraMAX modular wall formwork system | Contractor: Strobel, Coburg

Floor slab formwork

When less is enough

Aluminium beams reduce the number of props

When miniMAX aluminium beams are used to support the slab formwork, there is no “forest of props” below even 40 cm deep in situ concrete slabs.

Primary school, Ammerbuch-Altingen

Aluträger-System miniMAX | Baufirma Edbauer & Dormeyer, Haigerloch-Gruol

Structural works finished ahead of schedule for 200-bed hospital alongside Lake Starnberg

Contractor Kreuzer built 16 000 m² of floor slabs on Ischebeck TITAN HV formwork during the construction of the new Benedictus Hospital in Feldafing. The Ischebeck system with its aluminium beams and quick-action drop-heads speeds up work enormously.

Hospital, Feldafing

TITAN HV slab formwork | Contractor: Kreuzer, Bad Wörishofen

Put an end to that forest of props!

The miniMAX beams from Mayer Schaltechnik ensure safe, economic support during the construction of residential and industrial buildings.

Precast concrete planks plus in situ concrete topping were used for the six floors of a multi-storey car park in the Ostend district of Frankfurt am Main. To support the floors during construction, the contractor, Lupp, used the miniMAX system with its telescopic aluminium beams, which meant about 50% fewer props compared with the normal case.

Multi-storey car park, Frankfurt-Ostend

miniMAX aluminium beam system | Contractor: Lupp, Nidda

Thousands of props saved

miniMAX reduces work and costs for precast concrete floors

When the number of props to be set up, taken down and moved around on a building site is cut by 40–50%, then the cost-savings are very convincing.

Housing development, Fürth

miniMAX aluminium beam system | Contractor: Lupp, Nidda

Column formwork

Temporary corbels instead of falsework

Some 400 in situ concrete columns on a 10.0 x 7.5 m grid plus precast concrete beams and floor slabs form the loadbearing structure to this production building. Contractor Klebl cast the 6–7 m high columns using the PAX HD column formwork from Mayer Schaltechnik.

Production building, Lauf an der Pegnitz

PAX HD column formwork | Contractor: Klebl, Neumarkt

Accurate columns for “The Shelf”

MST’s PAX HD column formwork satisfies high standards in Berlin

The PAX HD folding column formwork can be used to build columns with square edges and a top-quality fair-face finish – a fact that the Lupp team demonstrated impressively on the “Pandion The Shelf” project in Berlin.

“Pandion The Shelf”, Berlin

Rechteckstützenschalung PAX HD | Baufirma Adolf Lupp, Niederlassung Berlin

Wall joint closure bars

Formwork joints sealed fast

Cavity wall elements are even more economic with the FLUXX system

For Rausch & Pausch GmbH, production had to begin as soon as possible in building No. 6 – 7500 m² of production area spread over four floors. The contractor, AS-Bau from Hof, completed the structural works in just four months.

Production building, Selb

FLUXX joint closure system for cavity walls | Contractor: AS-Bau, Hof

Excellent joints in record time

Building with precast concrete walls

A particularly time-saving method of construction using precast concrete elements was preferred for a new fire station in Leverkusen. FLUXX joint closure bars from Mayer Schaltechnik were used.

Fire station, Leverkusen

FLUXX joint closure system for cavity walls | Contractor: BAM Deutschland, Dresden branch

We look forward to hearing from you!

Completed

projects

Wall formwork

Floor slab formwork

Column formwork

Wall joint closure bars

Let’s talk about your project!

Mayer Schaltechnik GmbH

Newsletter

Kontaktanfrage

DE
EN

DE
EN

Enquiry Form

Enquiry Form
Worldwide Sales

Customer Advisory Board Request to join

Completed

projects

Wall formwork

Floor slab formwork

Column formwork

Wall joint closure bars

Let’s talk about your project!

Mayer Schaltechnik GmbH

Newsletter

Kontaktanfrage

DE EN

DE EN

Enquiry Form

Enquiry Form Worldwide Sales

Customer Advisory Board Request to join

DE
EN

DE
EN

Enquiry Form
Worldwide Sales